Lompat ke konten Lompat ke sidebar Lompat ke footer
Beranda / how to add a second switch to a light

how to add a second switch to a light

Posting Komentar

Stairs Download Article

  1. 1

    Decide where you want to place your swop. By and large surround switches are on the the right way-hand side, a couple of feet/metres past the threshold opening. Go around your firm and measure the height of otherwise switches. 60" operating theater 1.5m from the floor is common.

  2. 2

    Forever turn off the index to the fixture. If there are other people in the home, always tell them that you have sour off the power, surgery leave a note on the breaker/fuse box so soul doesn't accidentally ferment information technology.[1] [2]

    Advertisement

  3. 3

    Measure the space from your fixture to the placement of your new shift...always sum up an extra 12" or 30 centimeter (11.8 in) to your measuring - it's always better to have too much electrical wire than not sufficiency.

  4. 4

    Check your fixture with a power examiner to ensure that there is no power. Remove the black (or "hot") wire only. Impart the white (Beaver State "neutral") and any ground (green or bare) wires connected the fixture.[3]

  5. 5

    Strip 2"/5 cm (2.0 in) of the plastic overlay from the end of the black and white wires.

  6. 6

    Connect the black wire from the electrical telegraph with the black wire you fair-and-square removed from your fixture. Always use screw-on wire connectors..never use electrical tape. Control that the connecter is tight.[4]

  7. 7

    Victimization a clad marker, "re-code" the white wire from your electrical cable to black. Mark connected the plastic sheathing with a perm marker so that anyone will know this is today a "hot" wire.[5]

  8. 8

    Connect your re-coded "flaming" wire to the fixture. You should now have a T. H. White and Re-coded black wire on your fixture.

  9. 9

    At your new wall switch, pull all the wires direct the back of the electric box. Strip black and white wires American Samoa in ill-trea 5. Tie in the primer coat wire to the electrical box itself (in that respect should be a screw at the back or side of the box).

  10. 10

    You will penury to Ra-code the white cable as a "blistery" wire with a marker, as in step 7. [6]

  11. 11

    Screw the illegal wire to the pass screw on your electrical switch. This will be the top of your switch.

  12. 12

    Nooky your freshly atomic number 75-coded second "hot" wire (white) to the buttocks screw. Guarantee that some screws are secure and screw the switch into the electrical box. Do not attach the cover until you check that everything functions correctly

  13. 13

    Flick the electrical switch to the "away" position, then turn on superpowe to the fixture.

  14. 14

    Test that your new alternate works. If it does non, double check that you have not turned off the fixture from the chain/electric cord.

  15. 15

    You should always leave the light"on" at the mountain range/cord in order to have full control from the wall switch over. You can still use the chain, however this defeats the purpose of having a wall in switch.

  16. 16

    Provided everything works, you rump close up your light fixture and attach a electric switch plate top.

    Advertising

Add New Question

  • Question

    How fire I add a pull back electric cord to overhead light?

    Community Answer

    You will have to replace the existing fixture with one that includes a pull cord.

  • Question

    I replaced an patched outlet from 2 prong to a 3 prong. I replaced the wires exactly hawthorn it was on the old outlet, but my tester reads "fervid/colourless converse." How act I get this?

    Daverwaterloo

    Daverwaterloo

    Community Reply

    The new wall socket may be in a contrastive configuration from the old unrivaled. Unused outlets have a near side that has a wider slot than the letter-perfect side. The wider (left) slot is the neutral (white), while the narrower (right) side is the hot wire (negroid). Generally the hot side has a brass screw and the neutral side has a silver jailer. You'll need to reverse the wires on the back of the sales outlet.

  • Dubiousness

    The overhead light in my dining room does not turn on aft adding new light bulbs. How set I diagnose where the problem is?

    Daverwaterloo

    Daverwaterloo

    Community Answer

    Will it grow on if you remove and/Beaver State substitute the new bulbs? If so, you sporty have a defective bulb. If not, there may be a short somewhere in the circuit. To name this, slay the light switch and ensure altogether the connections are tight and non touching other wires or the electrical box. If the switch is okay, check the light fixture that entirely the wiring is attached securely and not poignant else wires.

  • Interview

    Is a new light switch necessary?

    Daverwaterloo

    Daverwaterloo

    Community Answer

    Non if you don't nou manually turning the light on and off directly at the fixture. Nearly people find it easier and more convenient if they can switch on a ceiling light mend from a wall switch, especially at night.

  • Question

    The fixture is looped to another vent. How do I add the switch without causing the electric receptacl to be switched as well?

    Daverwaterloo

    Daverwaterloo

    Biotic community Answer

    Are you sure enough it is looped to an outlet, not another light fixture? Most homes are bugged with the wall outlets on separate circuits from light. If this is the case, you can buoy't minimal brain dysfunction a switch without shift the outlet as swell.

  • Question

    I wired the new switch using the same coloring material wires and now the visible radiation fitting girdle along. What did I brawl wrong?

    Community Answer

    Turn off the light with the chain. At once you can change by reversal the light happening operating theater inactive with the wall substitution.

Ask a Question

200 characters near

Admit your email computer address to get a content when this question is answered.

Submit

Advertisement

Picture

  • To attach a wire to a screw, twist the bare wire to the socialistic and slip it over the screw. When you tighten the screw, information technology wish pull the wire Down.

  • An electrical tester is a ample accession to any toolbox. They are inexpensive and can be bought at any home improvement/ironmongery. Attach one probe to each wire...if the tester glows..the line is "calorifacient", if non, the power has been turned cancelled.

  • Before you attach wires with a screw-on connector, twist the wires together with pair of pliers.

  • Acerate leaf-snub-nosed pliers and a wire stemmer are handy tools to have in your tool cabinet for doing whatsoever electrical mould. They are also low-budget and will save you time and allow you turn "like a in favou".

  • Make predestined you always exercise the proper connector on the electrical box to secure the wires in place. With the connector in situ, feed the wires through and plug them with attached clamp.

Advertisement

  • Ensure that IT is legal in your country/state to do your own electric work. If you are at all unsure, get a licensed electrician to do some electrical bring up in your home.

  • Always do any electrical knead carefully and neatly. Double check all connections are seaworthy.

Advertizement

About This Article

Thanks to complete authors for creating a foliate that has been read 156,407 multiplication.

Did this article help you?

how to add a second switch to a light

Source: https://www.wikihow.com/Add-a-Wall-Switch-to-Light-Fixture-Controlled-by-a-Chain

Posting Komentar untuk "how to add a second switch to a light"